XDS560V2无法调试

经检测，卡在这里：

Loaded FPGA Image: C:\ti\ccs1011\ccs\ccs_base\common\uscif\dtc_top.jbc

The library build date was 'Nov 8 2020'.

The library build time was '16:14:07'.

The library package version is '9.2.1.00042'.

The library component version is '35.35.0.0'.

Shine：

请问用的是哪款器件？是自己的板子还是EVM板？这个错误是在点击target configuration file里的test connection时出现的吗？

,

Ping Pong：

你好，是6678。evm板。不是，是点verify出现的

,

Shine：

请问点的是哪里的"verify"? 请看一下下面的wiki网站，看板载仿真器是否能连？
processors.wiki.ti.com/…/Connecting_To_An_LCEVM_with_CCS

,

Ping Pong：

,

Ping Pong：

你好，附上了verify的截图。以及，板载的没问题，以下为板载 仿真器的verify输出
[Start]

Execute the command:

%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity

[Result]

—–[Print the board config pathname(s)]————————————

C:\Users\kites\AppData\Local\TEXASI~1\CCS\ti\1\0\BrdDat\testBoard.dat

—–[Print the reset-command software log-file]—————————–

This utility has selected a 100- or 510-class product.
This utility will load the adapter 'jioserdesusb.dll'.
The library build date was 'Nov8 2020'.
The library build time was '17:25:15'.
The library package version is '9.2.1.00042'.
The library component version is '35.35.0.0'.
The controller does not use a programmable FPGA.
The controller has a version number of '4' (0x00000004).
The controller has an insertion length of '0' (0x00000000).
This utility will attempt to reset the controller.
This utility has successfully reset the controller.

—–[Print the reset-command hardware log-file]—————————–

The scan-path will be reset by toggling the JTAG TRST signal.
The controller is the FTDI FT2232 with USB interface.
The link from controller to target is direct (without cable).
The software is configured for FTDI FT2232 features.
The controller cannot monitor the value on the EMU[0] pin.
The controller cannot monitor the value on the EMU[1] pin.
The controller cannot control the timing on output pins.
The controller cannot control the timing on input pins.
The scan-path link-delay has been set to exactly '0' (0x0000).

—–[The log-file for the JTAG TCLK output generated from the PLL]———-

There is no hardware for programming the JTAG TCLK frequency.

—–[Measure the source and frequency of the final JTAG TCLKR input]——–

There is no hardware for measuring the JTAG TCLK frequency.

—–[Perform the standard path-length test on the JTAG IR and DR]———–

This path-length test uses blocks of 64 32-bit words.

The test for the JTAG IR instruction path-length succeeded.
The JTAG IR instruction path-length is 6 bits.

The test for the JTAG DR bypass path-length succeeded.
The JTAG DR bypass path-length is 1 bits.

—–[Perform the Integrity scan-test on the JTAG IR]————————

This test will use blocks of 64 32-bit words.
This test will be applied just once.

Do a test using 0xFFFFFFFF.
Scan tests: 1, skipped: 0, failed: 0
Do a test using 0x00000000.
Scan tests: 2, skipped: 0, failed: 0
Do a test using 0xFE03E0E2.
Scan tests: 3, skipped: 0, failed: 0
Do a test using 0x01FC1F1D.
Scan tests: 4, skipped: 0, failed: 0
Do a test using 0x5533CCAA.
Scan tests: 5, skipped: 0, failed: 0
Do a test using 0xAACC3355.
Scan tests: 6, skipped: 0, failed: 0
All of the values were scanned correctly.

The JTAG IR Integrity scan-test has succeeded.

—–[Perform the Integrity scan-test on the JTAG DR]————————

This test will use blocks of 64 32-bit words.
This test will be applied just once.

Do a test using 0xFFFFFFFF.
Scan tests: 1, skipped: 0, failed: 0
Do a test using 0x00000000.
Scan tests: 2, skipped: 0, failed: 0
Do a test using 0xFE03E0E2.
Scan tests: 3, skipped: 0, failed: 0
Do a test using 0x01FC1F1D.
Scan tests: 4, skipped: 0, failed: 0
Do a test using 0x5533CCAA.
Scan tests: 5, skipped: 0, failed: 0
Do a test using 0xAACC3355.
Scan tests: 6, skipped: 0, failed: 0
All of the values were scanned correctly.

The JTAG DR Integrity scan-test has succeeded.

[End]

,

Shine：

请看一下仿真器是不是进入了safe mode了?
processors.wiki.ti.com/…/Emulator_safemode.pdf
www.einfochips.com/…/C6657-Lite-EVM_FAQ.pdf

,

Ping Pong：

你好，没有进入safe mode

,

Shine：

请尝试一下用低版本的CCS是否可以连接？

,

Ping Pong：

你好，也不行

,

Shine：

请问这个仿真器是第一次使用就不行么？建议联系一下blackhawk技术支持看是不是仿真器本身的问题。
www.blackhawk-dsp.com/…/xds560v2

,

Ping Pong：

你好，不是，是突然不能使用的。请问这个得找blackhawk解决吗？谢谢

,

Shine：

建议找一下blackhawk，看是否要更新一下FPGA程序。

,

Ping Pong：

你好，我们用config utility更新到最新版本了，也不行

,

Shine：

手头有其他仿真器吗？如果其他仿真器可以连板子的话，说明Mezzanine 560v2仿真器可以能坏了。

,

Ping Pong：

你好，有2个560v2，都是一样的情况

,

Shine：

这两个仿真器能连其他板子吗？确定一下是仿真器的问题还是板子的问题。

,

Ping Pong：

你好，不是。是最近才不行的。问一下是确定是仿真器的问题吗？因为似乎不能排除ti这边的问题

,

Shine：

这个需要做交叉实验，才能确定是仿真器的问题还是板子的问题。