您好,
1.電壓使用3.3V,掃頻及ADC測試正常,電壓調整為5V,依JP1及JP2設定後掃頻及ADC測試時,無訊號。
Susan Yang:
请问您JP1 JP2是如何连接的?您是如何供电的?另外您的图片有些模糊,我无法看清您的设置。
JP1 OFF 5V circuitry is not used. Provides power to AFE circuitry. Can be used for power measurement.
JP2 3.3VTX Enables 3.3-V circuitry. 5-V circuitry is not used
user6243928:
回复 Susan Yang:
您好,
使用3.3V:JP2(3.3VTX)、JP1 OFF。
使用5V:JP2(5VTX)、JP1 ON。
若有訊息,請不吝告知,謝謝。
下列圖示為5V JP1/JP2V:
Susan Yang:
回复 user6243928:
不知您是否参考下面的文档
在4 AFE Configuration 中有相关描述
对于AFE电路的供电:To use the same voltage source as the MCU, set JP3. To use an external voltage source, remove the jumper from JP3 and apply voltage to TP1 (V+) and TP2 (GND)
4.3 5-V Enable
The AFE includes a DC/DC step-up converter to enable 5-V TX voltage. To enable the step up converter, set JP1. For 5-V operation, also set JP2 for 5-V operation
user6243928:
回复 Susan Yang:
Susan Yang,您好
謝謝你的回覆。
現在接線方式與PDF文件相同,使用USB Power 5V時無訊號。
若有訊息,請不吝提供,下列為USB Power 3.3V、USB Power 5V評估板的設置方式,若有問題,再請告知,謝謝。
這是3.3V接線方式:
JP1(3VTX)、JP2(OFF)
這是使用5v的接線方式:
JP1(5VTX)、JP2(ON),其他設置與3.3V相同。
Susan Yang:
回复 user6243928:
USB Power 5V?
您的Figure 1. Power Selection即 S5 (POW_SEL) 设置的是EZ-FET,也就是说,您现在板子是靠右侧的USB来供电的?
然后您的AFE Configuration使用的是the same voltage source as the MCU,因为您的JP3是连接的
但是您现在是想使用5v
根据说明 JP1Provides 5-V power to the AFE circuitry. 而若是JP3连接的话,就是使用的the same voltage source as the MCU
所以建议您断开JP3试试
PS: 我手边暂时没有板子,所以无法测试,请您先试一下
user6243928:
回复 Susan Yang:
Susan Yang,您好
是的,板子是靠右側USB來供電。
依上述建議斷開JP3,使用USB Power 時,掃頻無法量測。
若有訊息,請不吝指導,謝謝。
下列為TI評估板狀況:
Susan Yang:
回复 user6243928:
等我周一回到办公室来测试一下,请等待一下 谢谢
Susan Yang:
回复 user6243928:
请参考上图的跳线设置,并在AFE3V3上加外部电源5V
这样就达到了AFE部分使用外部5V电源的要求