TI中文支持网
TI专业的中文技术问题咨询交流网站

C2000-GANG 无法存储程序,出现错误

C2000-GANG,驱动正常,通电正常,软件最新版本,运行时 点保存或者支行直接跳出错误 ,或者闪退。

TDI Fuse  keys  1-8 全是error

Susan Yang:

请问您是否有进行Self Test?

如 www.ti.com/…/spruhs0c.pdf

的 2.4 Self Test

所示,是否是成功的?若是不成功的话,请上传以下您的test report文件,谢谢

user1616268:

回复 Susan Yang:

有进行检测,

=== C2000-GANG Self test results ( Thursday, May 14, 2020, 14:26:32 ) ===

Adapter SN ——: 17101253 Hardware ——–: C2K : 01.04Access key ——: C2000 – Gang Programmer Silicon Number –: 8A26 1147 0C00 2B00API Firmware —-: C2K-Gang AC28: 01.00.04.06BOOT Firmware —: G430BOOT B430: 01.00.02.00GUI Software —-: C2000-Gang-GUI G28x: 01.00.03.00DLL Software —-: C2000-Gang-DLL D280: 01.00.03.00

================ Test results =============

No. name parameter limits result status

1: Data Bus (ALL LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK << 2: Data Bus (ALL HIGH) 0x00FF (0xFFFF – 0xFFFF) Result: 0xFFFF … >> OK << 3: Data Bus (D-0 HI ) 0x0001 (0x0101 – 0x0101) Result: 0x0101 … >> OK << 4: Data Bus (D-1 HI ) 0x0002 (0x0202 – 0x0202) Result: 0x0202 … >> OK << 5: Data Bus (D-2 HI ) 0x0004 (0x0404 – 0x0404) Result: 0x0404 … >> OK << 6: Data Bus (D-3 HI ) 0x0008 (0x0808 – 0x0808) Result: 0x0808 … >> OK << 7: Data Bus (D-4 HI ) 0x0010 (0x1010 – 0x1010) Result: 0x1010 … >> OK << 8: Data Bus (D-5 HI ) 0x0020 (0x2020 – 0x2020) Result: 0x2020 … >> OK << 9: Data Bus (D-6 HI ) 0x0040 (0x4040 – 0x4040) Result: 0x4040 … >> OK << 10: Data Bus (D-7 HI ) 0x0080 (0x8080 – 0x8080) Result: 0x8080 … >> OK <<

11: Data-2 Bus (ALL LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK << 12: Data-2 Bus (ALL HIGH) 0x00FF (0xFFFF – 0xFFFF) Result: 0xFFFF … >> OK << 13: Data-2 Bus (D2-0 HI ) 0x0001 (0x0101 – 0x0101) Result: 0x0101 … >> OK << 14: Data-2 Bus (D2-1 HI ) 0x0002 (0x0202 – 0x0202) Result: 0x0202 … >> OK << 15: Data-2 Bus (D2-2 HI ) 0x0004 (0x0404 – 0x0404) Result: 0x0404 … >> OK << 16: Data-2 Bus (D2-3 HI ) 0x0008 (0x0808 – 0x0808) Result: 0x0808 … >> OK << 17: Data-2 Bus (D2-4 HI ) 0x0010 (0x1010 – 0x1010) Result: 0x1010 … >> OK << 18: Data-2 Bus (D2-5 HI ) 0x0020 (0x2020 – 0x2020) Result: 0x2020 … >> OK << 19: Data-2 Bus (D2-6 HI ) 0x0040 (0x4040 – 0x4040) Result: 0x4040 … >> OK << 20: Data-2 Bus (D2-7 HI ) 0x0080 (0x8080 – 0x8080) Result: 0x8080 … >> OK <<

21: Vcc Target-1 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 3.29 V … >> ERROR << 22: Vcc Target-2 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.02 V … >> OK << 23: Vcc Target-3 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 24: Vcc Target-4 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 25: Vcc Target-5 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 26: Vcc Target-6 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 27: Vcc Target-7 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 28: Vcc Target-8 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK <<

29: Translators VT (OFF) 0.00 V ( 0.00 to 0.50) Result: 0.01 V … >> OK << 30: Translators VT (ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.24 V … >> OK <<

31: Vpp Voltage-in 10.00 V ( 8.00 to 12.00) Result: 10.75 V … >> OK << 32: Vpp Voltage 7.00 V ( 6.50 to 7.30) Result: 6.86 V … >> OK << 33: Internal Vcc-3.3V 3.30 V ( 3.20 to 3.40) Result: 3.31 V … >> OK <<

34: Vcc Target-1 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 35: Vcc Target-2 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.13 V … >> ERROR << 36: Vcc Target-3 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 37: Vcc Target-4 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 38: Vcc Target-5 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 39: Vcc Target-6 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 40: Vcc Target-7 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 41: Vcc Target-8 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR <<

42: Vcc discharge (50ms)Target-1 3.30 V ( 0.30 to 1.50) Result: 3.29 V … >> ERROR << 43: Vcc discharge (50ms)Target-2 3.30 V ( 0.30 to 1.50) Result: 0.17 V … >> ERROR << 44: Vcc discharge (50ms)Target-3 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR << 45: Vcc discharge (50ms)Target-4 3.30 V ( 0.30 to 1.50) Result: 0.17 V … >> ERROR << 46: Vcc discharge (50ms)Target-5 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR << 47: Vcc discharge (50ms)Target-6 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR << 48: Vcc discharge (50ms)Target-7 3.30 V ( 0.30 to 1.50) Result: 0.17 V … >> ERROR << 49: Vcc discharge (50ms)Target-8 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR <<

50: Vcc Target-1 ( #1 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 51: Vcc Target-2 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 52: Vcc Target-3 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 53: Vcc Target-4 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 54: Vcc Target-5 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 55: Vcc Target-6 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 56: Vcc Target-7 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 57: Vcc Target-8 ( #1 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 58: Vcc Target-1 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 59: Vcc Target-2 ( #2 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.17 V … >> ERROR << 60: Vcc Target-3 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 61: Vcc Target-4 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 62: Vcc Target-5 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 63: Vcc Target-6 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 64: Vcc Target-7 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 65: Vcc Target-8 ( #2 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 66: Vcc Target-1 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 67: Vcc Target-2 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 68: Vcc Target-3 ( #3 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.17 V … >> ERROR << 69: Vcc Target-4 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 70: Vcc Target-5 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 71: Vcc Target-6 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 72: Vcc Target-7 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 73: Vcc Target-8 ( #3 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 74: Vcc Target-1 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 75: Vcc Target-2 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 76: Vcc Target-3 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 77: Vcc Target-4 ( #4 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR << 78: Vcc Target-5 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 79: Vcc Target-6 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 80: Vcc Target-7 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 81: Vcc Target-8 ( #4 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 82: Vcc Target-1 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 83: Vcc Target-2 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 84: Vcc Target-3 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 85: Vcc Target-4 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 86: Vcc Target-5 ( #5 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR << 87: Vcc Target-6 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 88: Vcc Target-7 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 89: Vcc Target-8 ( #5 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 90: Vcc Target-1 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 91: Vcc Target-2 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 92: Vcc Target-3 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 93: Vcc Target-4 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 94: Vcc Target-5 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 95: Vcc Target-6 ( #6 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR << 96: Vcc Target-7 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 97: Vcc Target-8 ( #6 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 98: Vcc Target-1 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 99: Vcc Target-2 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<100: Vcc Target-3 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<101: Vcc Target-4 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<102: Vcc Target-5 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<103: Vcc Target-6 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<104: Vcc Target-7 ( #7 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.17 V … >> ERROR <<105: Vcc Target-8 ( #7 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<106: Vcc Target-1 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR <<107: Vcc Target-2 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<108: Vcc Target-3 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<109: Vcc Target-4 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<110: Vcc Target-5 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<111: Vcc Target-6 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<112: Vcc Target-7 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<113: Vcc Target-8 ( #8 ON ) 3.30 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR <<

114: SD Power OFF 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<115: SD Power ON 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<116: SD Discharge – delay 2ms 0x0010 (0x0001 – 0x0001) Result: 0x01 … >> OK <<117: SD Discharge – delay 50ms 0x0010 (0x0000 – 0x0000) Result: 0x00 … >> OK <<

118: BSL RX bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<119: BSL RX bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<120: BSL RX bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<121: BSL RX bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<122: BSL RX bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<123: BSL RX bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<124: BSL RX bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<125: BSL RX bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

126: BSL TX bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<127: BSL TX bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<128: BSL TX bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<129: BSL TX bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<130: BSL TX bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<131: BSL TX bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<132: BSL TX bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<133: BSL TX bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

134: TDI bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x81 … >> ERROR <<135: TDI bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<136: TDI bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x03 … >> ERROR <<137: TDI bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x05 … >> ERROR <<138: TDI bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x09 … >> ERROR <<139: TDI bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x11 … >> ERROR <<140: TDI bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x21 … >> ERROR <<141: TDI bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x41 … >> ERROR <<

142: TDIO Tx-bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<143: TDIO Tx-bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<144: TDIO Tx-bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<145: TDIO Tx-bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<146: TDIO Tx-bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<147: TDIO Tx-bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<148: TDIO Tx-bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<149: TDIO Tx-bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

150: TDIO Tx-Rx (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<151: TDIO Tx-Rx (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<152: TDIO Tx-Rx (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<153: TDIO Tx-Rx (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<154: TDIO Tx-Rx (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<155: TDIO Tx-Rx (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<156: TDIO Tx-Rx (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<157: TDIO Tx-Rx (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

158: TDIO Rx-bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<159: TDIO Rx-bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<160: TDIO Rx-bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<161: TDIO Rx-bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<162: TDIO Rx-bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<163: TDIO Rx-bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<164: TDIO Rx-bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<165: TDIO Rx-bus (#84 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

166: TMS bus (All HIGH) 0x00FF (0x00FF – 0x00FF) Result: 0xFF … >> OK <<167: TMS bus (All LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<

168: TMS bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<169: TMS bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<170: TMS bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<171: TMS bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<172: TMS bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<173: TMS bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<174: TMS bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<175: TMS bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

176: RST bus (All HIGH) 0x00FF (0x00FF – 0x00FF) Result: 0xFF … >> OK <<177: RST bus (All LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<

178: RST bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x00 … >> ERROR <<179: RST bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<180: RST bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<181: RST bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<182: RST bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<183: RST bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<184: RST bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<185: RST bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<

186: Keys buffer (All pull-up) 0x001F (0x001F – 0x001F) Result: 0x1F … >> OK <<

187: Access to LCD RAM (0xAA) 0x00AA (0x00AA – 0x00AA) Result: 0xAA … >> OK <<188: Access to LCD RAM (0x99) 0x0099 (0x0099 – 0x0099) Result: 0x99 … >> OK <<

189: Image Flash Access (get ID) 0x0002 (0x0001 – 0x0002) Result: 0x00 … >> ERROR <<

190: TDI Fuse keys (#1 ON) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<191: TDI Fuse keys (#2 ON) 0x0002 (0x0002 – 0x0002) Result: 0x03 … >> ERROR <<192: TDI Fuse keys (#3 ON) 0x0004 (0x0004 – 0x0004) Result: 0x05 … >> ERROR <<193: TDI Fuse keys (#4 ON) 0x0008 (0x0008 – 0x0008) Result: 0x09 … >> ERROR <<194: TDI Fuse keys (#5 ON) 0x0010 (0x0010 – 0x0010) Result: 0x11 … >> ERROR <<195: TDI Fuse keys (#6 ON) 0x0020 (0x0020 – 0x0020) Result: 0x21 … >> ERROR <<196: TDI Fuse keys (#7 ON) 0x0040 (0x0040 – 0x0040) Result: 0x41 … >> ERROR <<197: TDI Fuse keys (#8 ON) 0x0080 (0x0080 – 0x0080) Result: 0x81 … >> ERROR <<

198: TEST Fuse keys (#1 ON) 1.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<199: TEST Fuse keys (#2 ON) 2.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<200: TEST Fuse keys (#3 ON) 3.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<201: TEST Fuse keys (#4 ON) 4.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<202: TEST Fuse keys (#5 ON) 5.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<203: TEST Fuse keys (#6 ON) 6.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<204: TEST Fuse keys (#7 ON) 7.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<205: TEST Fuse keys (#8 ON) 8.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<

============== Finished =================================* Test failed!! 54 error(s).

Susan Yang:

回复 user1616268:

您现在是连接板子测试的?

The Gang Splitter must be connected to the C2000 Gang Programmer. Disconnect all target devices, because any connected devices can modify the test results and make them invalid.

user1616268:

回复 Susan Yang:

是的,现在就是连接目标板 点存储程序后 错误或者直接闪退。

user1616268:

回复 user1616268:

Susan Yang:

回复 user1616268:

很抱歉,可能我之前描述的有问题

您现在测试self test 的时候是否连接板子? self test 时是不可以连接板子的

我们现在应该先确认self test 的时候是可以正常通过的,即 C2000-GANG Self test results 这个报告是正确的,以确保C2000 GANG本身硬件以及功能是没有问题的

user1616268:

回复 Susan Yang:

不连接板子测试是OK的,连接板子 对软件编程时出现闪退 和报错

user1616268:

回复 user1616268:

现在就是连接板子 对器件 编程 闪退,文件也保存不了验证删除也操作不了 直接就闪退

user1616268:

回复 user1616268:

user1616268:

回复 user1616268:

还有电脑上驱动显示的是MSP-GANG的,,这个设备是C2000-GANG 为什么,

赞(0)
未经允许不得转载:TI中文支持网 » C2000-GANG 无法存储程序,出现错误
分享到: 更多 (0)