TI中文支持网
TI专业的中文技术问题搜集分享网站

为什么msp430x54xA_adc12_01.c进入不了中断处理程序?

大家好:

     我们购买了M430F5438A几套开发板,希望进行FFT的开发!

    我们将正弦信号接入开发板的P6.7端口,幅值1.2V.

    驱动程序主要的修改如下:

    “   ADC12CTL0 |= ADC12ENC;

  

        P6SEL |= 0x01;                            // P6.0 ADC option select

        P1DIR |= BIT0;                            // P1.0 output   ”

     修改为:

      “   ADC12CTL0 |= ADC12ENC;

  

         P6SEL |= = BIT0 + BIT1 + BIT2;                            // P6.7 ADC option select

         P1DIR |= BIT0;                            // P1.0 output  ”

    源程序地址如下:

dev.ti.com/…/node

Susan Yang:

我会在测试后给您回复

user5274273:

回复 Susan Yang:

谢谢!
更新一下,我们采用恒定的正弦信号(频率:1500HZ;幅值MAX=2.24V, 幅值MIN=190mV)
可以达到0x7ff以上(0.5AVcc)吧?
我们更关注的是输出数值,还是应当将幅值向上调一些?

user5274273:

回复 Susan Yang:

抱歉!

仍然没有结果!请参考截图

Susan Yang:

回复 user5274273:

我是使用CCS 10试的,0-2V的正弦波,代码如下

/* --COPYRIGHT--,BSD_EX* Copyright (c) 2012, Texas Instruments Incorporated* All rights reserved.** Redistribution and use in source and binary forms, with or without* modification, are permitted provided that the following conditions* are met:** *Redistributions of source code must retain the above copyright*notice, this list of conditions and the following disclaimer.** *Redistributions in binary form must reproduce the above copyright*notice, this list of conditions and the following disclaimer in the*documentation and/or other materials provided with the distribution.** *Neither the name of Texas Instruments Incorporated nor the names of*its contributors may be used to endorse or promote products derived*from this software without specific prior written permission.** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,* THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR* CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,* EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,* PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;* OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,* WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR* OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.**********************************************************************************MSP430 CODE EXAMPLE DISCLAIMER** MSP430 code examples are self-contained low-level programs that typically* demonstrate a single peripheral function or device feature in a highly* concise manner. For this the code may rely on the device's power-on default* register values and settings such as the clock configuration and care must* be taken when combining code from several examples to avoid potential side* effects. Also see www.ti.com/grace for a GUI- and www.ti.com/msp430ware* for an API functional library-approach to peripheral configuration.** --/COPYRIGHT--*/
//******************************************************************************
//MSP430F543xA Demo - ADC12_A, Sample A0, Set P1.0 if A0 > 0.5*AVcc
//
//Description: A single sample is made on A0 with reference to AVcc.
//Software sets ADC12SC to start sample and conversion - ADC12SC
//automatically cleared at EOC. ADC12 internal oscillator times sample (16x)
//and conversion. In mainloopwaits in LPM0 to save power until ADC12
//conversion complete, ADC12_ISR will force exit from LPM0 in Mainloop on
//reti. If A0 > 0.5*AVcc, P1.0 set, else reset.
//
//MSP430F5438A
//-----------------
///|\||
//| ||
//--|RST|
//||
//Vin -->|P6.0/A0P1.0|--> LED
//
//M Morales
//Texas Instruments Inc.
//June 2009
//Built with CCE Version: 3.2.2 and IAR Embedded Workbench Version: 4.2
//******************************************************************************#include <msp430.h>
int temp;
int main(void)
{WDTCTL = WDTPW + WDTHOLD;// Stop WDTADC12CTL0 = ADC12SHT02 + ADC12ON;// Sampling time, ADC12 onADC12CTL1 = ADC12SHP;// Use sampling timerADC12IE = 0x01;// Enable interruptADC12CTL0 |= ADC12ENC;P6SEL |= 0x80;// P6.0 ADC option select P6.7P1DIR |= BIT0;// P1.0 output__delay_cycles(10000);while (1){ADC12CTL0 |= ADC12SC;// Start sampling/conversion__bis_SR_register(LPM0_bits + GIE);// LPM0, ADC12_ISR will force exit__no_operation();// For debugger}
}#if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__)
#pragma vector = ADC12_VECTOR
__interrupt void ADC12_ISR(void)
#elif defined(__GNUC__)
void __attribute__ ((interrupt(ADC12_VECTOR))) ADC12_ISR (void)
#else
#error Compiler not supported!
#endif
{switch(__even_in_range(ADC12IV,34)){case0: break;// Vector0:No interruptcase2: break;// Vector2:ADC overflowcase4: break;// Vector4:ADC timing overflowcase6:// Vector6:ADC12IFG0temp = ADC12MEM0;if (ADC12MEM0 >= 0x7ff)// ADC12MEM = A0 > 0.5AVcc?P1OUT |= BIT0;// P1.0 = 1elseP1OUT &= ~BIT0;// P1.0 = 0__bic_SR_register_on_exit(LPM0_bits);// Exit active CPUbreak;case8: break;// Vector8:ADC12IFG1case 10: break;// Vector 10:ADC12IFG2case 12: break;// Vector 12:ADC12IFG3case 14: break;// Vector 14:ADC12IFG4case 16: break;// Vector 16:ADC12IFG5case 18: break;// Vector 18:ADC12IFG6case 20: break;// Vector 20:ADC12IFG7case 22: break;// Vector 22:ADC12IFG8case 24: break;// Vector 24:ADC12IFG9case 26: break;// Vector 26:ADC12IFG10case 28: break;// Vector 28:ADC12IFG11case 30: break;// Vector 30:ADC12IFG12case 32: break;// Vector 32:ADC12IFG13case 34: break;// Vector 34:ADC12IFG14default: break;}
}

user5274273:

回复 Susan Yang:

谢谢!

请参考我们的环境!

赞(0)
未经允许不得转载:TI中文支持网 » 为什么msp430x54xA_adc12_01.c进入不了中断处理程序?
分享到: 更多 (0)