TI中文支持网之前debug仿真一直好好的，突然某一次debug就弹出错误，如下：
Error connecting to the target:
(Error -1015 @ 0x0)
Device is not responding to the request. Device may be locked, or the emulator connection may be unreliable. Unlock the device if possible (e.g. use wait in reset mode, and power-cycle the board). If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.232.0)
用的是SEED XDS510PLUS仿真器，CCS5，TMS320F28335
这是什么原因啊？？求助，感谢～～～
Hank Zhao：
可能是F28335被加密或者仿真器连接有问题，按照提示在target configuration file中将TCLK的频率降低一点再重新上电连接。
之前debug仿真一直好好的，突然某一次debug就弹出错误，如下：
Error connecting to the target:
(Error -1015 @ 0x0)
Device is not responding to the request. Device may be locked, or the emulator connection may be unreliable. Unlock the device if possible (e.g. use wait in reset mode, and power-cycle the board). If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.232.0)
用的是SEED XDS510PLUS仿真器，CCS5，TMS320F28335
这是什么原因啊？？求助，感谢～～～
WIND JXC：
回复 Hank Zhao:
试过了还是不行呢~~~最讨厌用DSP了，感觉好脆弱。。。。
TI的大神们就没个QQ么
之前debug仿真一直好好的，突然某一次debug就弹出错误，如下：
Error connecting to the target:
(Error -1015 @ 0x0)
Device is not responding to the request. Device may be locked, or the emulator connection may be unreliable. Unlock the device if possible (e.g. use wait in reset mode, and power-cycle the board). If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.232.0)
用的是SEED XDS510PLUS仿真器，CCS5，TMS320F28335
这是什么原因啊？？求助，感谢～～～
WIND JXC：
回复 Hank Zhao:
CCS5.5会不会出问题了呢？
之前debug仿真一直好好的，突然某一次debug就弹出错误，如下：
Error connecting to the target:
(Error -1015 @ 0x0)
Device is not responding to the request. Device may be locked, or the emulator connection may be unreliable. Unlock the device if possible (e.g. use wait in reset mode, and power-cycle the board). If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.232.0)
用的是SEED XDS510PLUS仿真器，CCS5，TMS320F28335
这是什么原因啊？？求助，感谢～～～
WIND JXC：
回复 Hank Zhao:
现在又报这个错误
Error connecting to the target:(Error -171 @ 0x0)The wrong controller address value has been used.A controller cannot be detected even though theselected port does match the hardware configuration.(Emulation package 5.1.232.0)
大神，这个又是什么原因？？？感谢~~~
之前debug仿真一直好好的，突然某一次debug就弹出错误，如下：
Error connecting to the target:
(Error -1015 @ 0x0)
Device is not responding to the request. Device may be locked, or the emulator connection may be unreliable. Unlock the device if possible (e.g. use wait in reset mode, and power-cycle the board). If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.232.0)
用的是SEED XDS510PLUS仿真器，CCS5，TMS320F28335
这是什么原因啊？？求助，感谢～～～
Hank Zhao：
回复 WIND JXC:
你在target configuration file中配置好仿真器和device后，test一下连接看是什么情况。然后将F28335的boot引脚配置为check boot mode,再test一下。
之前debug仿真一直好好的，突然某一次debug就弹出错误，如下：
Error connecting to the target:
(Error -1015 @ 0x0)
Device is not responding to the request. Device may be locked, or the emulator connection may be unreliable. Unlock the device if possible (e.g. use wait in reset mode, and power-cycle the board). If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.232.0)
用的是SEED XDS510PLUS仿真器，CCS5，TMS320F28335
这是什么原因啊？？求助，感谢～～～
rookiecalf：
回复 Hank Zhao:
看看硬件焊接有没有问题
