TI中文支持网
TI专业的中文技术问题搜集分享网站

DLP4710: 烧写internal pattern时曝光时间设置较长无法采集到8位灰度图

Part Number:DLP4710EVM-LCOther Parts Discussed in Thread:DLP4710

请问,DLP4710的曝光时间设置范围是多大呢?八位灰度调制方式是什么呢?

如下图所示,烧写6张竖条纹8位灰度图,曝光时间设置为33000us,前后黑暗时间按照提示设为接近最小值。

给出触发信号trigger out 2,相机同步用trigger width模式采集。但是采集到图像如下图所示,无法采集到8位灰度图。

如果将曝光时间设置为8000us,无论帧频高达100帧以上还是降到30帧,都可以采集到8位灰度图。

上述情况的原因是什么呢?为什么无法在曝光时间较大时低帧频使用?

DLP_Tech:

这种情况是相机保管时间设置不合理,确保满足以下条件即可:

相机exposure time ≥ DLP exposure time 

,

Lu Wong:

按照您的建议设置了相机Timed曝光模式,且曝光时间大于DLP曝光时间,如下图所示,仍然无法采集到八位灰度图。

,

Jeremy_Wu:

测量触发和camera曝光同步如何?波形。

,

Lu Wong:

相机和投影仪应该是同步的,测试了投影仪触发输出信号(黄色)和相机接收到触发信号后自定义IO输出frame trigger wait信号。此时投影仪设置曝光时间41690us,相机为trigger width曝光模式。但是采集到的仍然不是八位灰度图。

,

Jeremy_Wu:

https://software-dl.ti.com/dlp/pico-fw-selector/release_notes/FWSel_DLPC3479_DLPA3005_pm2_i2c0x36_v8p1p1.html

Supported pattern timings in Sequence Database v0.1.10:

Internal Pattern Mode Timings:

Pattern Type
Sequence Index
Exposure Time Range (us)
Sequence Min Pre-Exposure Dark Time (us)
Sequence Min Post-Exposure Dark Time (us)

1-bit Monochrome
18
200 – 399
171
31

17
400 – 799
171
31

16
800 – 799
171
31

15
1800 – 3799
171
31

14
3800 – 7600
171
31

1-bit RGB
25
600 – 1799
171
31

24
1800 – 3799
171
31

23
3800 – 7600
171
31

8-bit Monochrome
20
2084 – 4168
171
31

21*
1677 – 2083
171
31

8-bit RGB
22
6512 – 13024
171
31

*Sequence 21 is a special sequence that displays 7-bit patterns. The least significant bit of the 8-bit pattern data will be ignored.

Notes:

For internal patterns, there will be an additional variable delay of ~3000 us at the beginning of every pattern set.
Exposure times shorter than the above values are not possible. Longer exposure times will operate with decreased timing accuracy and behavior is not guaranteed.
Shorter dark times are not possible. Longer dark times can be used. The maximum possible dark times for a desired exposure time are:

Tmax pre-exposure dark time  = ( 27306us + tsequence min pre-exposure dark time ) * (Tdesired exposure / tsequence minimum exposure)
Tmax post-exposure dark time = ( 27306us + tsequence min post-exposure dark time ) * (Tdesired exposure / tsequence minimum exposure)

你使用一张Pattern测试看能否拍摄到?

,

Lu Wong:

使用一张pattern,曝光时间设置41690us,拍摄结果如下:

使用一张pattern,曝光时间设置18000us,拍摄结果如下:

赞(0)
未经允许不得转载:TI中文支持网 » DLP4710: 烧写internal pattern时曝光时间设置较长无法采集到8位灰度图
分享到: 更多 (0)

© 2024 TI中文支持网   网站地图 鲁ICP备2022002796号-1