Part Number:AWR1843BOOSTOther Parts Discussed in Thread: DCA1000EVM, MMWAVE-STUDIO, AWR1843
hi,
我想仅仅使用AWR1843BOOST与DCA1000数据采集板(不使用mmWave Studio)利用我自己的工程使用以太网完成ADC数据的采集。首先我自己的工程是在AWR1843BOOST上运行,而且我在自己工程中有将ADC数据通过LVDS发出,然后再通过DCA1000数据采集板将其发送到自己的PC机上。请问,我需要如何一步一步实现?比如DCA1000数据采集板如何设置?
Shine:
请参考下面的FAQ里的方法。https://e2e.ti.com/support/sensors-group/sensors/f/sensors-forum/856054/faq-raw-adc-data-capture-from-mmwave-sensor
Q11. How to control DCA1000EVM without mmWave Studio configuration?
Answer: In new version of mmWave Studio we are providing DCA1000-CLI tool (<mmwave_studio_02_01_00_00>\mmWaveStudio\PostProc\DCA1000EVM_CLI_Control.exe) and its source code which can be used for this purpose.
Follow the documentation mmwave_sdk_user_guide.pdf (section 3.3.2 from mmwave SDK) and DCA1000EVM_CLI_Software_User_guide.pdf (from mmWave Studio <mmwave-studio>\mmWaveStudio\ReferenceCode\DCA1000\Docs) where it explain the usage step for this CLI tool.
Here are a few threads which provide the alternate solution to capture data using Studio but without doing any device configuration from it.
https://www.ti2k.com/wp-content/uploads/ti2k/DeyiSupport_传感器_2812538#2812538
https://www.ti2k.com/wp-content/uploads/ti2k/DeyiSupport_传感器_2928751#2928751
,
?? ?:
谢谢您给出的链接。
我并不想通过DCA1000-CLI tool去实现ADC数据的采集。
为了简化问题,我想先利用自己的工程将ADC数据或自定义数据通过LVDS发出到DCA1000 EVM再通过以太网传送到PC。为了达到此目的,以下:
首先我想知道AWR1843 boost在自己写的工程中(不是demo程序)使用LVDS传输ADC数据或自定义数据时需要设置什么?比如AWR1843 boost板子上的SOP0,SOP1, SOP2分别需要设置什么(当前我设置为SOP0=1;SOP1=0;SOP2=0)?并且不连接DCA1000 EVM与PC之间的USB cable (J1-Radar FTDI)。
其次,如何知道或验证ADC数据已经通过LVDS传送到了DCA1000 EVM?
最后,DCA1000 EVM需要抓取ADC数据并通过以太网发送ADC数据到PC,这一步中的DCA1000 EVM(在硬件与软件上)需要做什么设置?
而在PC中我想通过wireshark来监控网包数据是否正确发出。
谢谢!
,
Chris Meng:
?? ? 说:首先我想知道AWR1843 boost在自己写的工程中(不是demo程序)使用LVDS传输ADC数据或自定义数据时需要设置什么?比如AWR1843 boost板子上的SOP0,SOP1, SOP2分别需要设置什么(当前我设置为SOP0=1;SOP1=0;SOP2=0)?并且不连接DCA1000 EVM与PC之间的USB cable (J1-Radar FTDI)。
请参考mmw demo里lvds stream的实现。使用的是functional mode。
?? ? 说:其次,如何知道或验证ADC数据已经通过LVDS传送到了DCA1000 EVM?
你可以测量lvds上的信号。
可以使用DCA1000EVM_CLI配置DCA1000EVM并采集数据来验证你自己代码的LVDS输出。
?? ? 说:最后,DCA1000 EVM需要抓取ADC数据并通过以太网发送ADC数据到PC,这一步中的DCA1000 EVM(在硬件与软件上)需要做什么设置?
请在DCA1000EVM user guide里搜索hardware configuration。
——————————————————————-
下面是studio-CLI tool的信息供参考.
https://www.ti2k.com/wp-content/uploads/ti2k/DeyiSupport_传感器_node
(+) IWR6843: Where is the code to save raw file in Studio CLI GUI? – Sensors forum – Sensors – TI E2E support forums