AM5708: AM5708 USB dongle 相容性問題

Hi Sir

我們發現多個USB dongle在am5708的機種上無法正常讀寫，

但在am3352上的機種可以正常讀寫(不需要額外接USB hub)，或am5708額外接USB hub (with extra power)也可以正常使用，

做過的HW實驗如下，沒有改善

1. 拿掉USB 電阻
2. 拿掉USB 電阻 + 拿掉powe switch

• am5708 Linux Kernel 4.14.79 TI SDK-05.03.00.07
• am3352 Linux Kernel 3.2.0 TI am335x-evm-sdk-src-06.00.00.00

請問有建議嗎?

謝謝

Daniel

Shine：

请问是TI的板子还是自己的板子？log打印信息是什么？

,

Daniel Cheng1：

Hi Shine

目前發現USB 2.0的USB dongle都沒問題,問題都是出在USB3.0的USB dongle

請問有什麼可以確認嗎?

是客製化的板子,log請參閱附件

謝謝

Danielkernel.log

[11:38:02.305]# dmesg
[11:38:02.306][0.000000] Booting Linux on physical CPU 0x0
[11:38:02.317][0.000000] Linux version 4.14.79 (fatek@asus-debian-fatek) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #1 SMP PREEMPT Thu Dec 2 14:02:50 CST 2021
[11:38:02.328][0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[11:38:02.328][0.000000] CPU: div instructions available: patching division code
[11:38:02.339][0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[11:38:02.339][0.000000] OF: fdt: Machine model: TI AM5708 1119b
[11:38:02.351][0.000000] Memory policy: Data cache writealloc
[11:38:02.351][0.000000] efi: Getting EFI parameters from FDT:
[11:38:02.361][0.000000] efi: UEFI not found.
[11:38:02.362][0.000000] cma: Reserved 24 MiB at 0x00000000be400000
[11:38:02.373][0.000000] OMAP4: Map 0x00000000bfd00000 to fe600000 for dram barrier
[11:38:02.373][0.000000] On node 0 totalpages: 212224
[11:38:02.388][0.000000] free_area_init_node: node 0, pgdat c124d640, node_mem_map ef6f2000
[11:38:02.388][0.000000]DMA zone: 1728 pages used for memmap
[11:38:02.388][0.000000]DMA zone: 0 pages reserved
[11:38:02.395][0.000000]DMA zone: 147456 pages, LIFO batch:31
[11:38:02.395][0.000000]HighMem zone: 64768 pages, LIFO batch:15
[11:38:02.395][0.000000] DRA722 ES2.1
[11:38:02.407][0.000000] percpu: Embedded 16 pages/cpu @ef695000 s35468 r8192 d21876 u65536
[11:38:02.418][0.000000] pcpu-alloc: s35468 r8192 d21876 u65536 alloc=16*4096
[11:38:02.418][0.000000] pcpu-alloc: [0] 0[11:38:02.429][0.000000] Built 1 zonelists, mobility grouping on.Total pages: 210496
[11:38:02.439][0.000000] Kernel command line: console=ttyS2,115200n8 vt.global_cursor_default=0 quiet root=PARTUUID=bdc484bd-02 ro rootfstype=ext4 rootwait
[11:38:02.441][0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[11:38:02.451][0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[11:38:02.452][0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[11:38:02.461][0.000000] Memory: 798416K/848896K available (10240K kernel code, 319K rwdata, 2712K rodata, 2048K init, 286K bss, 25904K reserved, 24576K cma-reserved, 234496K highmem)
[11:38:02.475][0.000000] Virtual kernel memory layout:
[11:38:02.485][0.000000]vector: 0xffff0000 - 0xffff1000(4 kB)
[11:38:02.486][0.000000]fixmap: 0xffc00000 - 0xfff00000(3072 kB)
[11:38:02.496][0.000000]vmalloc : 0xf0800000 - 0xff800000( 240 MB)
[11:38:02.496][0.000000]lowmem: 0xc0000000 - 0xf0000000( 768 MB)
[11:38:02.507][0.000000]pkmap: 0xbfe00000 - 0xc0000000(2 MB)
[11:38:02.507][0.000000]modules : 0xbf000000 - 0xbfe00000(14 MB)
[11:38:02.518][0.000000].text : 0xc0008000 - 0xc0c00000(12256 kB)
[11:38:02.518][0.000000].init : 0xc1000000 - 0xc1200000(2048 kB)
[11:38:02.530][0.000000].data : 0xc1200000 - 0xc124ff58( 320 kB)
[11:38:02.530][0.000000].bss : 0xc1251000 - 0xc1298988( 287 kB)
[11:38:02.541][0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[11:38:02.541][0.000000] Preemptible hierarchical RCU implementation.
[11:38:02.552][0.000000]RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[11:38:02.552][0.000000]Tasks RCU enabled.
[11:38:02.562][0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[11:38:02.563][0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[11:38:02.574][0.000000] GIC: Using split EOI/Deactivate mode
[11:38:02.575][0.000000] OMAP clockevent source: timer1 at 32786 Hz
[11:38:02.586][0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[11:38:02.597][0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[11:38:02.598][0.000006] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns
[11:38:02.607][0.000017] Switching to timer-based delay loop, resolution 162ns
[11:38:02.619][0.000414] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[11:38:02.621][0.000421] OMAP clocksource: 32k_counter at 32768 Hz
[11:38:02.629][0.000959] Console: colour dummy device 80x30
[11:38:02.641][0.000989] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475)
[11:38:02.641][0.001004] pid_max: default: 32768 minimum: 301
[11:38:02.653][0.001137] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[11:38:02.653][0.001150] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[11:38:02.663][0.001803] CPU: Testing write buffer coherency: ok
[11:38:02.664][0.001843] CPU0: Spectre v2: using ICIALLU workaround
[11:38:02.675][0.002075] CPU0: update cpu_capacity 1024
[11:38:02.675][0.002086] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[11:38:02.686][0.039834] Setting up static identity map for 0x80200000 - 0x80200060
[11:38:02.686][0.059840] Hierarchical SRCU implementation.
[11:38:02.686][0.080067] EFI services will not be available.
[11:38:02.697][0.099909] smp: Bringing up secondary CPUs ...
[11:38:02.698][0.099918] smp: Brought up 1 node, 1 CPU
[11:38:02.709][0.099927] SMP: Total of 1 processors activated (12.29 BogoMIPS).
[11:38:02.710][0.099934] CPU: All CPU(s) started in HYP mode.
[11:38:02.720][0.099940] CPU: Virtualization extensions available.
[11:38:02.720][0.100459] devtmpfs: initialized
[11:38:02.731][0.122337] random: get_random_u32 called from bucket_table_alloc+0x108/0x230 with crng_init=0
[11:38:02.732][0.130133] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[11:38:02.742][0.130462] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[11:38:02.753][0.130478] futex hash table entries: 256 (order: 2, 16384 bytes)
[11:38:02.754][0.131212] pinctrl core: initialized pinctrl subsystem
[11:38:02.764][0.131806] DMI not present or invalid.
[11:38:02.765][0.132094] NET: Registered protocol family 16
[11:38:02.776][0.141391] DMA: preallocated 256 KiB pool for atomic coherent allocations
[11:38:02.777][0.142357] omap_hwmod: l3_main_2 using broken dt data from ocp
[11:38:02.787][0.347152] cpuidle: using governor ladder
[11:38:02.787][0.347186] cpuidle: using governor menu
[11:38:02.787][0.362390] gpio gpiochip0: (gpio): added GPIO chardev (254:0)
[11:38:02.798][0.362543] gpiochip_setup_dev: registered GPIOs 0 to 31 on device: gpiochip0 (gpio)
[11:38:02.808][0.362618] OMAP GPIO hardware version 0.1
[11:38:02.809][0.363618] gpio gpiochip1: (gpio): added GPIO chardev (254:1)
[11:38:02.820][0.363763] gpiochip_setup_dev: registered GPIOs 32 to 63 on device: gpiochip1 (gpio)
[11:38:02.820][0.364950] gpio gpiochip2: (gpio): added GPIO chardev (254:2)
[11:38:02.832][0.365163] gpiochip_setup_dev: registered GPIOs 64 to 95 on device: gpiochip2 (gpio)
[11:38:02.843][0.366887] gpio gpiochip3: (gpio): added GPIO chardev (254:3)
[11:38:02.843][0.367042] gpiochip_setup_dev: registered GPIOs 96 to 127 on device: gpiochip3 (gpio)
[11:38:02.854][0.368075] gpio gpiochip4: (gpio): added GPIO chardev (254:4)
[11:38:02.855][0.368217] gpiochip_setup_dev: registered GPIOs 128 to 159 on device: gpiochip4 (gpio)
[11:38:02.865][0.369229] gpio gpiochip5: (gpio): added GPIO chardev (254:5)
[11:38:02.876][0.369381] gpiochip_setup_dev: registered GPIOs 160 to 191 on device: gpiochip5 (gpio)
[11:38:02.876][0.371694] gpio gpiochip6: (gpio): added GPIO chardev (254:6)
[11:38:02.886][0.371842] gpiochip_setup_dev: registered GPIOs 192 to 223 on device: gpiochip6 (gpio)
[11:38:02.887][0.372927] gpio gpiochip7: (gpio): added GPIO chardev (254:7)
[11:38:02.905][0.373078] gpiochip_setup_dev: registered GPIOs 224 to 255 on device: gpiochip7 (gpio)
[11:38:02.905][0.412180] No ATAGs?
[11:38:02.910][0.412225] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[11:38:02.921][0.412233] hw-breakpoint: maximum watchpoint size is 8 bytes.
[11:38:02.921][0.412810] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[11:38:02.933][0.412820] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[11:38:02.933][0.413476] OMAP DMA hardware revision 0.0
[11:38:02.942][0.483195] edma 43300000.edma: memcpy is disabled
[11:38:02.943][0.487649] edma 43300000.edma: TI EDMA DMA engine driver
[11:38:02.954][0.518433] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[11:38:02.969][0.519511] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-vmain[0]'
[11:38:02.976][0.520322] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-v3_3d[0]'
[11:38:02.988][0.520707] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-vtt[0]'
[11:38:02.988][0.522792] vtt_fixed: supplied by V3_3D
[11:38:02.999][0.523346] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-ads7846-reg[0]'
[11:38:03.005][0.526344] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[11:38:03.010][0.526915] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[11:38:03.010][0.527350] omap-iommu 58882000.mmu: 58882000.mmu registered
[11:38:03.022][0.527782] omap-iommu 55082000.mmu: 55082000.mmu registered
[11:38:03.022][0.530687] SCSI subsystem initialized
[11:38:03.033][0.532251] usbcore: registered new interface driver usbfs
[11:38:03.033][0.532369] usbcore: registered new interface driver hub
[11:38:03.044][0.532503] usbcore: registered new device driver usb
[11:38:03.044][0.535059] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[11:38:03.054][0.535965] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz
[11:38:03.055][0.537083] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[11:38:03.055][0.537426] media: Linux media interface: v0.10
[11:38:03.066][0.537533] Linux video capture interface: v2.00
[11:38:03.066][0.537793] pps_core: LinuxPPS API ver. 1 registered
[11:38:03.077][0.537800] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[11:38:03.078][0.537881] PTP clock support registered
[11:38:03.090][0.537960] EDAC MC: Ver: 3.0.0
[11:38:03.090][0.539070] dmi: Firmware registration failed.
[11:38:03.105][0.539788] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[11:38:03.105][0.540173] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[11:38:03.110][0.542120] Advanced Linux Sound Architecture Driver Initialized.
[11:38:03.111][0.551687] clocksource: Switched to clocksource arch_sys_counter
[11:38:03.121][0.572877] NET: Registered protocol family 2
[11:38:03.122][0.573459] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[11:38:03.136][0.573533] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[11:38:03.145][0.573687] TCP: Hash tables configured (established 8192 bind 8192)
[11:38:03.145][0.573771] UDP hash table entries: 512 (order: 2, 16384 bytes)
[11:38:03.156][0.573808] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[11:38:03.156][0.573960] NET: Registered protocol family 1
[11:38:03.156][0.573992] PCI: CLS 0 bytes, default 64
[11:38:03.166][0.575401] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[11:38:03.178][0.575668] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[11:38:03.178][0.578501] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[11:38:03.188][0.593820] fuse init (API version 7.26)
[11:38:03.190][0.599528] bounce: pool size: 64 pages
[11:38:03.202][0.599603] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[11:38:03.202][0.599613] io scheduler noop registered
[11:38:03.203][0.599620] io scheduler deadline registered
[11:38:03.211][0.599743] io scheduler cfq registered (default)
[11:38:03.212][0.599751] io scheduler mq-deadline registered
[11:38:03.223][0.599759] io scheduler kyber registered
[11:38:03.223][0.609737] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[11:38:03.236][0.609985] pinctrl-single 4a002e8c.pinmux: please update dts to use #pinctrl-cells = <1>
[11:38:03.245][0.610068] pinctrl-single 4a002e8c.pinmux: initialized with no interrupts
[11:38:03.245][0.610078] pinctrl-single 4a002e8c.pinmux: 1 pins at pa fc002e8c size 4
[11:38:03.256][0.619570] pwm-backlight backlight: GPIO lookup for consumer enable
[11:38:03.256][0.619582] pwm-backlight backlight: using device tree for GPIO lookup
[11:38:03.268][0.619597] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/backlight[0]'
[11:38:03.278][0.619607] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/backlight[0]'
[11:38:03.290][0.619616] pwm-backlight backlight: using lookup tables for GPIO lookup
[11:38:03.291][0.619626] pwm-backlight backlight: lookup for GPIO enable failed
[11:38:03.305][0.619648] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[11:38:03.305][0.627736] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[11:38:03.311][0.632747] console [ttyS2] disabled
[11:38:03.324][0.632802] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 43, base_baud = 3000000) is a 8250
[11:38:03.324][0.633797] 4806e000.serial: ttyS3 at MMIO 0x4806e000 (irq = 44, base_baud = 3000000) is a 8250
[11:38:03.335][0.635051] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 45, base_baud = 3000000) is a 8250
[11:38:03.346][0.636334] 48068000.serial: ttyS5 at MMIO 0x48068000 (irq = 46, base_baud = 3000000) is a 8250
[11:38:03.356][0.637150] 48420000.serial: ttyS6 at MMIO 0x48420000 (irq = 47, base_baud = 3000000) is a 8250
[11:38:03.357][0.639968] omap_rng 48090000.rng: Random Number Generator ver. 20
[11:38:03.357][0.642351] DSS: OMAP DSS rev 6.1
[11:38:03.367][0.643915] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops)
[11:38:03.381][0.647701] panel-dpi display: GPIO lookup for consumer enable
[11:38:03.382][0.647710] panel-dpi display: using device tree for GPIO lookup
[11:38:03.390][0.647724] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/display[0]'
[11:38:03.402][0.647734] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/display[0]'
[11:38:03.402][0.647743] panel-dpi display: using lookup tables for GPIO lookup
[11:38:03.412][0.647752] panel-dpi display: lookup for GPIO enable failed
[11:38:03.413][0.647762] panel-dpi display: GPIO lookup for consumer reset
[11:38:03.424][0.647770] panel-dpi display: using device tree for GPIO lookup
[11:38:03.436][0.647780] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/display[0]'
[11:38:03.437][0.647790] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/display[0]'
[11:38:03.446][0.647798] panel-dpi display: using lookup tables for GPIO lookup
[11:38:03.457][0.647806] panel-dpi display: lookup for GPIO reset failed
[11:38:03.458][0.647833] panel-dpi display: display supply vcc not found, using dummy regulator
[11:38:03.458][0.666875] brd: module loaded
[11:38:03.470][0.676474] loop: module loaded
[11:38:03.470][0.679805] m25p80 spi2.0: mr25h10 (128 Kbytes)
[11:38:03.479][0.679831] 1 ofpart partitions found on MTD device spi2.0
[11:38:03.480][0.679838] Creating 1 MTD partitions on "spi2.0":
[11:38:03.492][0.679849] 0x000000000000-0x000000100000 : "mram"
[11:38:03.493][0.679857] mtd: partition "mram" extends beyond the end of device "spi2.0" -- size truncated to 0x20000
[11:38:03.502][0.684081] mdio_bus fixed-0: GPIO lookup for consumer reset
[11:38:03.502][0.684091] mdio_bus fixed-0: using lookup tables for GPIO lookup
[11:38:03.514][0.684101] mdio_bus fixed-0: lookup for GPIO reset failed
[11:38:03.515][0.684131] libphy: Fixed MDIO Bus: probed
[11:38:03.525][0.688994] mdio_bus 48485000.mdio: GPIO lookup for consumer reset
[11:38:03.525][0.689004] mdio_bus 48485000.mdio: using lookup tables for GPIO lookup
[11:38:03.535][0.689013] mdio_bus 48485000.mdio: lookup for GPIO reset failed
[11:38:03.547][0.741712] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000
[11:38:03.547][0.741722] davinci_mdio 48485000.mdio: detected phy mask fffffffc
[11:38:03.558][0.745881] libphy: 48485000.mdio: probed
[11:38:03.558][0.745894] davinci_mdio 48485000.mdio: phy[0]: device 48485000.mdio:00, driver Micrel KSZ8081 or KSZ8091
[11:38:03.570][0.745904] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01, driver Micrel KSZ9031 Gigabit PHY
[11:38:03.581][0.746814] cpsw 48484000.ethernet: Detected MACID = 68:47:49:d6:97:c8
[11:38:03.581][0.746890] cpsw 48484000.ethernet: initialized cpsw ale version 1.4
[11:38:03.592][0.746899] cpsw 48484000.ethernet: ALE Table size 1024
[11:38:03.602][0.747878] cpsw 48484000.ethernet: cpsw: Detected MACID = 68:47:49:d6:97:c9
[11:38:03.603][0.749128] PPP generic driver version 2.4.2
[11:38:03.603][0.750835] NET: Registered protocol family 24
[11:38:03.613][0.750863] ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
[11:38:03.614][0.750869] ipw2100: Copyright(c) 2003-2006 Intel Corporation
[11:38:03.625][0.751005] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2k
[11:38:03.636][0.751012] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[11:38:03.637][0.751134] libipw: 802.11 data/management/control stack, git-1.1.13
[11:38:03.648][0.751140] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[11:38:03.653][0.751265] usbcore: registered new interface driver cdc_ether
[11:38:03.659][0.751374] usbcore: registered new interface driver cdc_eem
[11:38:03.660][0.751499] usbcore: registered new interface driver cdc_ncm
[11:38:03.670][0.751606] usbcore: registered new interface driver huawei_cdc_ncm
[11:38:03.681][0.751786] usbcore: registered new interface driver cdc_mbim
[11:38:03.681][0.756617] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[11:38:03.681][0.756626] ehci-pci: EHCI PCI platform driver
[11:38:03.693][0.756807] ehci-omap: OMAP-EHCI Host Controller driver
[11:38:03.693][0.758070] usbcore: registered new interface driver usblp
[11:38:03.704][0.758174] usbcore: registered new interface driver cdc_wdm
[11:38:03.715][0.758302] usbcore: registered new interface driver usb-storage
[11:38:03.715][0.759161] userial_init: registered 4 ttyGS* devices
[11:38:03.715][0.759622] mousedev: PS/2 mouse device common for all mice
[11:38:03.726][0.760124] of_get_named_gpiod_flags: parsed 'pendown-gpio' property of node '/ocp/spi@480b8000/tsc2046@0[0]' - status (0)
[11:38:03.736][0.761345] ads7846 spi3.0: touchscreen, irq 168
[11:38:03.748][0.761818] input: ADS7846 Touchscreen as /devices/platform/44000000.ocp/480b8000.spi/spi_master/spi3/spi3.0/input/input0
[11:38:03.752][0.795653] rtc rtc0: rx8010: dev (253:0)
[11:38:03.760][0.795673] rtc-rx8010 1-0032: rtc core: registered rx8010 as rtc0
[11:38:03.761][0.795889] i2c /dev entries driver
[11:38:03.771][0.797403] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
[11:38:03.771][0.797482] vpe 489d0000.vpe: Direct firmware load for vpdma-1b8.bin failed with error -2
[11:38:03.782][0.797494] vpe 489d0000.vpe: couldn't get firmware
[11:38:03.782][0.798271] usbcore: registered new interface driver uvcvideo
[11:38:03.793][0.798278] USB Video Class driver (1.1.1)
[11:38:03.793][0.803462] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[11:38:03.803][0.805382] sdhci: Secure Digital Host Controller Interface driver
[11:38:03.804][0.805388] sdhci: Copyright(c) Pierre Ossman
[11:38:03.822][0.806599] sdhci-pltfm: SDHCI platform and OF driver helper
[11:38:03.822][0.808468] sdhci-omap 4809c000.mmc: GPIO lookup for consumer cd
[11:38:03.827][0.808477] sdhci-omap 4809c000.mmc: using device tree for GPIO lookup
[11:38:03.837][0.808492] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]'
[11:38:03.838][0.808503] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]'
[11:38:03.850][0.808512] sdhci-omap 4809c000.mmc: using lookup tables for GPIO lookup
[11:38:03.860][0.808521] sdhci-omap 4809c000.mmc: lookup for GPIO cd failed
[11:38:03.860][0.808532] sdhci-omap 4809c000.mmc: GPIO lookup for consumer wp
[11:38:03.871][0.808540] sdhci-omap 4809c000.mmc: using device tree for GPIO lookup
[11:38:03.890][0.808551] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]'
[11:38:03.890][0.808561] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]'
[11:38:03.894][0.808569] sdhci-omap 4809c000.mmc: using lookup tables for GPIO lookup
[11:38:03.894][0.808578] sdhci-omap 4809c000.mmc: lookup for GPIO wp failed
[11:38:03.905][0.809366] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_1_8v mode
[11:38:03.916][0.861716] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA
[11:38:03.922][0.862269] sdhci-omap 480b4000.mmc: GPIO lookup for consumer wp
[11:38:03.926][0.862278] sdhci-omap 480b4000.mmc: using device tree for GPIO lookup
[11:38:03.940][0.862291] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]'
[11:38:03.941][0.862303] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]'
[11:38:03.951][0.862311] sdhci-omap 480b4000.mmc: using lookup tables for GPIO lookup
[11:38:03.960][0.862320] sdhci-omap 480b4000.mmc: lookup for GPIO wp failed
[11:38:03.961][0.931708] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA
[11:38:03.971][0.933943] hidraw: raw HID events driver (C) Jiri Kosina
[11:38:03.972][0.934139] usbcore: registered new interface driver usbhid
[11:38:03.983][0.934145] usbhid: USB HID core driver
[11:38:03.989][0.934777] extcon-usb-gpio extcon_usb1: GPIO lookup for consumer id
[11:38:03.994][0.934786] extcon-usb-gpio extcon_usb1: using device tree for GPIO lookup
[11:38:04.006][0.934799] of_get_named_gpiod_flags: can't parse 'id-gpios' property of node '/extcon_usb1[0]'
[11:38:04.006][0.934850] of_get_named_gpiod_flags: parsed 'id-gpio' property of node '/extcon_usb1[0]' - status (0)
[11:38:04.017][0.934868] extcon-usb-gpio extcon_usb1: GPIO lookup for consumer vbus
[11:38:04.028][0.934876] extcon-usb-gpio extcon_usb1: using device tree for GPIO lookup
[11:38:04.028][0.934887] of_get_named_gpiod_flags: can't parse 'vbus-gpios' property of node '/extcon_usb1[0]'
[11:38:04.039][0.934917] of_get_named_gpiod_flags: parsed 'vbus-gpio' property of node '/extcon_usb1[0]' - status (0)
[11:38:04.053][0.935043] omap_gpio 4ae10000.gpio: Could not set line 0 debounce to 20000 microseconds (-22)
[11:38:04.060][0.944996] extcon-usb-gpio extcon_usb2: GPIO lookup for consumer id
[11:38:04.061][0.945090] extcon-usb-gpio extcon_usb2: using device tree for GPIO lookup
[11:38:04.072][0.945204] of_get_named_gpiod_flags: can't parse 'id-gpios' property of node '/extcon_usb2[0]'
[11:38:04.084][0.945258] of_get_named_gpiod_flags: parsed 'id-gpio' property of node '/extcon_usb2[0]' - status (0)
[11:38:04.085][0.945276] extcon-usb-gpio extcon_usb2: GPIO lookup for consumer vbus
[11:38:04.095][0.945285] extcon-usb-gpio extcon_usb2: using device tree for GPIO lookup
[11:38:04.105][0.945296] of_get_named_gpiod_flags: can't parse 'vbus-gpios' property of node '/extcon_usb2[0]'
[11:38:04.122][0.945325] of_get_named_gpiod_flags: parsed 'vbus-gpio' property of node '/extcon_usb2[0]' - status (0)
[11:38:04.122][0.945532] omap_gpio 4ae10000.gpio: Could not set line 3 debounce to 20000 microseconds (-22)
[11:38:04.130][0.947319] usbcore: registered new interface driver snd-usb-audio
[11:38:04.130][0.957386] ip_tables: (C) 2000-2006 Netfilter Core Team
[11:38:04.139][0.957613] arp_tables: arp_tables: (C) 2002 David S. Miller
[11:38:04.140][0.958420] NET: Registered protocol family 10
[11:38:04.151][0.959639] Segment Routing with IPv6
[11:38:04.151][0.959706] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[11:38:04.161][0.960606] NET: Registered protocol family 17
[11:38:04.162][0.960648] lib80211: common routines for IEEE802.11 drivers
[11:38:04.172][0.960656] lib80211_crypt: registered algorithm 'NULL'
[11:38:04.173][0.960663] lib80211_crypt: registered algorithm 'WEP'
[11:38:04.184][0.960670] lib80211_crypt: registered algorithm 'CCMP'
[11:38:04.184][0.960676] lib80211_crypt: registered algorithm 'TKIP'
[11:38:04.184][0.960698] Key type dns_resolver registered
[11:38:04.196][0.960823] omap_voltage_late_init: Voltage driver support not added
[11:38:04.196][0.960835] Power Management for TI OMAP4+ devices.
[11:38:04.207][0.961107] Registering SWP/SWPB emulation handler
[11:38:04.207][0.978047] dmm 4e000000.dmm: workaround for errata i878 in use
[11:38:04.218][0.979948] dmm 4e000000.dmm: initialized all PAT entries
[11:38:04.229][0.999779] ti-iodelay 4844a000.padconf: Set reg 0x18c Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.229][0.999795] ti-iodelay 4844a000.padconf: Set reg 0x1a4 Delay(a: 119 g: 0), Elements(C=0 F=3)0x29003
[11:38:04.239][0.999808] ti-iodelay 4844a000.padconf: Set reg 0x1b0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.253][0.999820] ti-iodelay 4844a000.padconf: Set reg 0x1bc Delay(a: 18 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.262][0.999832] ti-iodelay 4844a000.padconf: Set reg 0x1c8 Delay(a: 894 g: 0), Elements(C=2 F=1)0x29041
[11:38:04.274][0.999844] ti-iodelay 4844a000.padconf: Set reg 0x1d4 Delay(a: 30 g: 0), Elements(C=0 F=1)0x29001
[11:38:04.274][0.999855] ti-iodelay 4844a000.padconf: Set reg 0x1e0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.286][0.999867] ti-iodelay 4844a000.padconf: Set reg 0x1ec Delay(a: 23 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.295][0.999878] ti-iodelay 4844a000.padconf: Set reg 0x1f8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.308][0.999889] ti-iodelay 4844a000.padconf: Set reg 0x360 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.319][0.999900] ti-iodelay 4844a000.padconf: Set reg 0x194 Delay(a: 152 g: 0), Elements(C=0 F=5)0x29005
[11:38:04.320][0.999911] ti-iodelay 4844a000.padconf: Set reg 0x1ac Delay(a: 206 g: 0), Elements(C=0 F=6)0x29006
[11:38:04.329][0.999922] ti-iodelay 4844a000.padconf: Set reg 0x1b8 Delay(a: 78 g: 0), Elements(C=0 F=2)0x29002
[11:38:04.340][0.999932] ti-iodelay 4844a000.padconf: Set reg 0x1c4 Delay(a: 2 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.351][0.999943] ti-iodelay 4844a000.padconf: Set reg 0x1d0 Delay(a: 266 g: 0), Elements(C=0 F=8)0x29008
[11:38:04.364][0.999954] ti-iodelay 4844a000.padconf: Set reg 0x1dc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.364][0.999965] ti-iodelay 4844a000.padconf: Set reg 0x1e8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.374][0.999975] ti-iodelay 4844a000.padconf: Set reg 0x1f4 Delay(a: 43 g: 0), Elements(C=0 F=1)0x29001
[11:38:04.386][0.999986] ti-iodelay 4844a000.padconf: Set reg 0x200 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.396][0.999997] ti-iodelay 4844a000.padconf: Set reg 0x368 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.407][1.000007] ti-iodelay 4844a000.padconf: Set reg 0x190 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.408][1.000018] ti-iodelay 4844a000.padconf: Set reg 0x1a8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.421][1.000028] ti-iodelay 4844a000.padconf: Set reg 0x1b4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.430][1.000039] ti-iodelay 4844a000.padconf: Set reg 0x1c0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.441][1.000049] ti-iodelay 4844a000.padconf: Set reg 0x1d8 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.452][1.000060] ti-iodelay 4844a000.padconf: Set reg 0x1e4 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.453][1.000070] ti-iodelay 4844a000.padconf: Set reg 0x1f0 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.464][1.000081] ti-iodelay 4844a000.padconf: Set reg 0x1fc Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.476][1.000091] ti-iodelay 4844a000.padconf: Set reg 0x364 Delay(a: 0 g: 0), Elements(C=0 F=0)0x29000
[11:38:04.477][1.000535] mmc1: new DDR MMC card at address 0001
[11:38:04.486][1.001024] mmcblk1: mmc1:0001 Q2J54A 3.59 GiB[11:38:04.486][1.001311] mmcblk1boot0: mmc1:0001 Q2J54A partition 1 16.0 MiB
[11:38:04.498][1.001502] mmcblk1boot1: mmc1:0001 Q2J54A partition 2 16.0 MiB
[11:38:04.503][1.001765] mmcblk1rpmb: mmc1:0001 Q2J54A partition 3 512 KiB
[11:38:04.509][1.002639] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[11:38:04.520][1.002646] [drm] No driver support for vblank timestamp query.
[11:38:04.520][1.007511] [drm] Enabling DMM ywrap scrolling
[11:38:04.520][1.008716]mmcblk1: p1 p2 p3 p4
[11:38:04.531][1.090985] Console: switching to colour frame buffer device 128x37
[11:38:04.531][1.098565] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
[11:38:04.542][1.099880] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0
[11:38:04.553][1.102213] dwc3 48890000.usb: changing max_speed on rev 5533202a
[11:38:04.553][1.108116] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[11:38:04.565][1.108147] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[11:38:04.576][1.108462] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010
[11:38:04.576][1.108522] xhci-hcd xhci-hcd.0.auto: irq 174, io mem 0x488d0000
[11:38:04.587][1.108884] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[11:38:04.587][1.108896] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[11:38:04.598][1.108904] usb usb1: Product: xHCI Host Controller
[11:38:04.602][1.108913] usb usb1: Manufacturer: Linux 4.14.79 xhci-hcd
[11:38:04.609][1.108921] usb usb1: SerialNumber: xhci-hcd.0.auto
[11:38:04.609][1.109660] hub 1-0:1.0: USB hub found
[11:38:04.609][1.109773] hub 1-0:1.0: 1 port detected
[11:38:04.624][1.110271] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[11:38:04.632][1.110294] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[11:38:04.632][1.110312] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0SuperSpeed
[11:38:04.643][1.110408] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[11:38:04.643][1.110569] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[11:38:04.654][1.110579] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[11:38:04.665][1.110587] usb usb2: Product: xHCI Host Controller
[11:38:04.665][1.110595] usb usb2: Manufacturer: Linux 4.14.79 xhci-hcd
[11:38:04.665][1.110603] usb usb2: SerialNumber: xhci-hcd.0.auto
[11:38:04.675][1.111227] hub 2-0:1.0: USB hub found
[11:38:04.676][1.111269] hub 2-0:1.0: 1 port detected
[11:38:04.687][1.113893] Read PDN pin from device tree
[11:38:04.701][1.113909] of_get_named_gpiod_flags: can't parse 'ak4432,pdn-gpio' property of node '/ocp/i2c@48060000/audio-codec@19[0]'
[11:38:04.706][1.113917] ak4432 pdn pin(4294967294) is invalid(642)
[11:38:04.710][1.113933] of_get_named_gpiod_flags: can't parse 'ak4432,mute_gpio' property of node '/ocp/i2c@48060000/audio-codec@19[0]'
[11:38:04.711][1.113940] ak4432 mute pin(4294967294) is invalid(652)
[11:38:04.720][1.142143] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound@0[0]'
[11:38:04.732][1.142156] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound@0[0]'
[11:38:04.744][1.142706] asoc-simple-card sound@0: ak4432-aif <-> 48470000.mcasp mapping ok
[11:38:04.744][1.142722] asoc-simple-card sound@0: ASoC: no DMI vendor name!
[11:38:04.755][1.146274] rtc-rx8010 1-0032: setting system clock to 2021-12-21 11:08:13 UTC (1640084893)
[11:38:04.756][1.147002] ALSA device list:
[11:38:04.766][1.147009]#0: DRA7xx-EVM
[11:38:04.766][1.147051] Warning: unable to open an initial console.
[11:38:04.776][1.160702] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[11:38:04.788][1.160745] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[11:38:04.788][1.162590] devtmpfs: mounted
[11:38:04.788][1.164151] Freeing unused kernel memory: 2048K
[11:38:04.807][1.172677] random: fast init done
[11:38:04.807][1.230514] fatek_lcm_turn_on
[11:38:04.807][1.233366] fatek_init_usb_modules
[11:38:04.810][1.239835] udc 48890000.usb: registering UDC driver [g_cdc]
[11:38:04.811][1.239889] using random self ethernet address
[11:38:04.811][1.239898] using random host ethernet address
[11:38:04.821][1.240143] g_cdc gadget: adding config #1 'CDC Composite (ECM + ACM)'/bf002038
[11:38:04.838][1.240157] g_cdc gadget: adding 'cdc_ethernet'/ee626780 to config 'CDC Composite (ECM + ACM)'/bf002038
[11:38:04.839][1.240954] usb0: HOST MAC f6:9e:e1:96:a0:f8
[11:38:04.844][1.241054] usb0: MAC ae:50:ef:a3:5f:8c
[11:38:04.844][1.241074] g_cdc gadget: CDC Ethernet: dual speed IN/ep1in OUT/ep1out NOTIFY/ep2in
[11:38:04.855][1.241085] g_cdc gadget: adding 'acm'/ee6263c0 to config 'CDC Composite (ECM + ACM)'/bf002038
[11:38:04.868][1.241101] g_cdc gadget: acm ttyGS0: dual speed IN/ep3in OUT/ep2out NOTIFY/ep4in
[11:38:04.868][1.241109] g_cdc gadget: cfg 1/bf002038 speeds: high full
[11:38:04.878][1.241117] g_cdc gadget:interface 0 = cdc_ethernet/ee626780
[11:38:04.878][1.241125] g_cdc gadget:interface 1 = cdc_ethernet/ee626780
[11:38:04.889][1.241132] g_cdc gadget:interface 2 = acm/ee6263c0
[11:38:04.889][1.241138] g_cdc gadget:interface 3 = acm/ee6263c0
[11:38:04.905][1.241152] g_cdc gadget: CDC Composite Gadget, version: King Kamehameha Day 2008
[11:38:04.905][1.241159] g_cdc gadget: g_cdc ready
[11:38:04.910][1.247460] g_ffs: gfs_init()
[11:38:04.910][1.247476] functionfs_init()
[11:38:04.910][1.247488] file system registered
[11:38:04.911][1.249120] fatek_init_pictbridge
[11:38:04.923][1.251001] U7 series skip pictbridge function
[11:38:04.934][1.273889] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[11:38:04.934][1.423810] EXT4-fs (mmcblk1p3): recovery complete
[11:38:04.944][1.424632] EXT4-fs (mmcblk1p3): mounted filesystem with ordered data mode. Opts: (null)
[11:38:04.945][1.481287] EXT4-fs (mmcblk1p4): recovery complete
[11:38:04.956][1.482038] EXT4-fs (mmcblk1p4): mounted filesystem with ordered data mode. Opts: (null)
[11:38:04.956][1.824628] cpsw 48484000.ethernet eth0tmp: renamed from eth0
[11:38:04.966][1.850392] cpsw 48484000.ethernet eth1tmp: renamed from eth1
[11:38:04.978][1.870296] cpsw 48484000.ethernet eth1: renamed from eth0tmp
[11:38:04.979][1.890123] cpsw 48484000.ethernet eth0: renamed from eth1tmp
[11:38:04.989][1.963842] net eth0: initializing cpsw version 1.15 (0)
[11:38:05.000][2.152523] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:05.006][2.152686] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.011][2.159921] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:05.012][2.204095] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.022][2.366753] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:05.038][2.366903] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.045][2.372425] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:05.045][2.442592] usbcore: registered new interface driver usbserial
[11:38:05.057][2.442714] usbcore: registered new interface driver usbserial_generic
[11:38:05.057][2.442824] usbserial: USB Serial support registered for generic
[11:38:05.067][2.482961] usbcore: registered new interface driver usb_debug
[11:38:05.080][2.483085] usbserial: USB Serial support registered for debug
[11:38:05.080][2.483201] usbserial: USB Serial support registered for xhci_dbc
[11:38:05.090][2.541360] usbcore: registered new interface driver option
[11:38:05.090][2.541479] usbserial: USB Serial support registered for GSM modem (1-port)
[11:38:05.101][2.677512] RTW: module init start
[11:38:05.101][2.677523] RTW: rtl88x2bu v5.3.1_27678.20180430_COEX20180427-5959
[11:38:05.102][2.677529] RTW: build time: Dec2 2021 14:17:08
[11:38:05.112][2.677535] RTW: rtl88x2bu BT-Coex version = COEX20180427-5959
[11:38:05.113][2.677588] RTW: rtw_inetaddr_notifier_register
[11:38:05.124][2.677758] usbcore: registered new interface driver rtl88x2bu
[11:38:05.125][2.677766] RTW: module init ret=0
[11:38:05.139][2.748881] usbcore: registered new interface driver rtl8192cu
[11:38:05.139][2.788593] usbcore: registered new interface driver r8188eu
[11:38:05.146][2.835690] usbcore: registered new interface driver rtl8710bu
[11:38:05.146][2.912334] RTW: module init start
[11:38:05.156][2.912345] RTW: rtl8821cu v5.8.1.7_37266.20200929_COEX20200616-4141
[11:38:05.157][2.912351] RTW: rtl8821cu BT-Coex version = COEX20200616-4141
[11:38:05.168][2.912369] RTW: rtw_inetaddr_notifier_register
[11:38:05.168][2.912540] usbcore: registered new interface driver rtl8821cu
[11:38:05.168][2.912548] RTW: module init ret=0
[11:38:05.179][2.944869] usbcore: registered new interface driver mt7601u
[11:38:05.180][3.007396] usbcore: registered new interface driver rt2800usb
[11:38:05.190][3.058915] fatek_init_agent
[11:38:05.191][4.740663] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.201][4.836776] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:05.212][4.836937] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.224][4.840298] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:05.224][5.770767] net eth0: initializing cpsw version 1.15 (0)
[11:38:05.235][5.893090] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:05.246][5.893234] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.258][5.896548] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:05.258][7.841902] random: FvFirmware.frt: uninitialized urandom read (16 bytes read)
[11:38:05.269][8.407338] random: FvFirmware.frt: uninitialized urandom read (16 bytes read)
[11:38:05.270][8.499005] gs_open: ttyGS0 (ee74c800,ee7070c0)
[11:38:05.280][8.499080] gs_chars_in_buffer: (0,ee74c800) chars=0
[11:38:05.280][8.499109] gs_chars_in_buffer: (0,ee74c800) chars=0
[11:38:05.291][8.499792] gs_chars_in_buffer: (0,ee74c800) chars=0
[11:38:05.291][8.499801] gs_write_room: (0,ee74c800) room=0
[11:38:05.303][8.522491] random: FvFirmware.frt: uninitialized urandom read (16 bytes read)
[11:38:05.304][152.702108] random: crng init done
[11:38:05.304][152.702120] random: 7 urandom warning(s) missed due to ratelimiting
[11:38:05.313][ 1092.831824] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[11:38:05.325][ 1093.021490] usb 1-1: New USB device found, idVendor=0951, idProduct=1666
[11:38:05.325][ 1093.021505] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11:38:05.336][ 1093.021514] usb 1-1: Product: DataTraveler 3.0
[11:38:05.336][ 1093.021523] usb 1-1: Manufacturer: Kingston
[11:38:05.347][ 1093.021532] usb 1-1: SerialNumber: 60A44C413841F28109956329
[11:38:05.347][ 1093.029239] usb-storage 1-1:1.0: USB Mass Storage device detected
[11:38:05.359][ 1093.059417] scsi host0: usb-storage 1-1:1.0
[11:38:05.359][ 1094.084735] scsi 0:0:0:0: Direct-AccessKingston DataTraveler 3.0PQ: 0 ANSI: 6
[11:38:05.369][ 1094.088196] sd 0:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[11:38:05.370][ 1094.089397] sd 0:0:0:0: [sda] Write Protect is off
[11:38:05.381][ 1094.089409] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
[11:38:05.392][ 1094.090454] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[11:38:05.392][ 1094.095542]sda: sda1
[11:38:05.392][ 1094.098478] sd 0:0:0:0: [sda] Attached SCSI removable disk
[11:38:05.405][ 1132.521831] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.414][ 1136.861809] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.414][ 1141.201891] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.425][ 1145.541863] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.426][ 1145.542294] usb 1-1: USB disconnect, device number 2
[11:38:05.437][ 1145.547044] scsi 0:0:0:0: rejecting I/O to offline device
[11:38:05.437][ 1145.547064] scsi 0:0:0:0: killing request
[11:38:05.437][ 1145.904553] blk_partition_remap: fail for partition 1
[11:38:05.448][ 1148.346896] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.459][ 1148.446739] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:05.470][ 1148.446888] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.470][ 1148.450203] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:05.486][ 1149.765495] net eth0: initializing cpsw version 1.15 (0)
[11:38:05.492][ 1149.883428] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:05.504][ 1149.883581] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.504][ 1149.886930] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:05.515][ 1149.899968] net eth0: initializing cpsw version 1.15 (0)
[11:38:05.520][ 1149.912012] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.525][ 1150.014000] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:05.538][ 1150.014163] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.549][ 1150.017451] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:05.550][ 1154.251807] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.559][ 1154.251934] usb usb1-port1: attempt power cycle
[11:38:05.560][ 1154.961810] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[11:38:05.573][ 1155.003568] usb 1-1: New USB device found, idVendor=0951, idProduct=1666
[11:38:05.588][ 1155.003584] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11:38:05.589][ 1155.003594] usb 1-1: Product: DataTraveler 3.0
[11:38:05.589][ 1155.003602] usb 1-1: Manufacturer: Kingston
[11:38:05.592][ 1155.003611] usb 1-1: SerialNumber: 60A44C413841F28109956329
[11:38:05.593][ 1155.005467] usb-storage 1-1:1.0: USB Mass Storage device detected
[11:38:05.604][ 1155.037505] scsi host0: usb-storage 1-1:1.0
[11:38:05.604][ 1156.083948] scsi 0:0:0:0: Direct-AccessKingston DataTraveler 3.0PQ: 0 ANSI: 6
[11:38:05.620][ 1156.089569] sd 0:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[11:38:05.626][ 1156.090602] sd 0:0:0:0: [sda] Write Protect is off
[11:38:05.627][ 1156.090616] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
[11:38:05.638][ 1156.091645] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[11:38:05.638][ 1156.096852]sda: sda1
[11:38:05.649][ 1156.101173] sd 0:0:0:0: [sda] Attached SCSI removable disk
[11:38:05.650][ 1194.601858] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.661][ 1198.941808] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.661][ 1203.281857] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.672][ 1207.621833] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.672][ 1207.622268] usb 1-1: USB disconnect, device number 5
[11:38:05.683][ 1207.626162] scsi 0:0:0:0: rejecting I/O to offline device
[11:38:05.683][ 1207.626181] scsi 0:0:0:0: killing request
[11:38:05.694][ 1207.974494] blk_partition_remap: fail for partition 1
[11:38:05.695][ 1210.491064] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.704][ 1210.596683] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:05.719][ 1210.596831] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.727][ 1210.601208] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:05.727][ 1210.633357] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.739][ 1210.737603] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:05.750][ 1210.737751] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.751][ 1210.741064] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:05.760][ 1211.991826] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.772][ 1212.038843] net eth0: initializing cpsw version 1.15 (0)
[11:38:05.782][ 1212.166169] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:05.789][ 1212.166334] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.795][ 1212.170977] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:05.795][ 1212.182796] net eth0: initializing cpsw version 1.15 (0)
[11:38:05.805][ 1212.304935] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:05.822][ 1212.305100] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.828][ 1212.308372] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:05.828][ 1216.331905] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[11:38:05.840][ 1216.332059] usb usb1-port1: attempt power cycle
[11:38:05.840][ 1217.041813] usb 1-1: new high-speed USB device number 8 using xhci-hcd
[11:38:05.851][ 1217.083476] usb 1-1: New USB device found, idVendor=0951, idProduct=1666
[11:38:05.861][ 1217.083493] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11:38:05.862][ 1217.083503] usb 1-1: Product: DataTraveler 3.0
[11:38:05.862][ 1217.083512] usb 1-1: Manufacturer: Kingston
[11:38:05.873][ 1217.083520] usb 1-1: SerialNumber: 60A44C413841F28109956329
[11:38:05.888][ 1217.090360] usb-storage 1-1:1.0: USB Mass Storage device detected
[11:38:05.889][ 1217.122159] scsi host0: usb-storage 1-1:1.0
[11:38:05.895][ 1218.163935] scsi 0:0:0:0: Direct-AccessKingston DataTraveler 3.0PQ: 0 ANSI: 6
[11:38:05.895][ 1218.169231] sd 0:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[11:38:05.906][ 1218.170264] sd 0:0:0:0: [sda] Write Protect is off
[11:38:05.906][ 1218.170277] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
[11:38:05.918][ 1218.171293] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[11:38:05.918][ 1218.178679]sda: sda1
[11:38:05.928][ 1218.181530] sd 0:0:0:0: [sda] Attached SCSI removable disk
[11:38:05.929][ 1245.602222] usb 1-1: USB disconnect, device number 8
[11:38:05.941][ 1245.608637] scsi 0:0:0:0: rejecting I/O to offline device
[11:38:05.941][ 1245.608659] scsi 0:0:0:0: killing request
[11:38:05.941][ 1245.915578] blk_partition_remap: fail for partition 1
[11:38:05.950][ 1248.424847] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.961][ 1248.537691] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:05.972][ 1248.537840] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:05.973][ 1248.541791] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:05.986][ 1248.568723] net eth1: initializing cpsw version 1.15 (0)
[11:38:05.995][ 1248.667128] Micrel KSZ8081 or KSZ8091 48485000.mdio:00: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=48485000.mdio:00, irq=POLL)
[11:38:06.007][ 1248.667277] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:06.008][ 1248.670590] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[11:38:06.018][ 1249.968564] net eth0: initializing cpsw version 1.15 (0)
[11:38:06.028][ 1250.093861] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL)
[11:38:06.040][ 1250.094024] cpsw-phy-sel 4a002554.cpsw-phy-sel: RMII External clock is not supported
[11:38:06.041][ 1250.097381] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11:38:06.052][ 1252.341810] usb 1-1: new high-speed USB device number 9 using xhci-hcd
[11:38:06.052][ 1252.531399] usb 1-1: New USB device found, idVendor=0951, idProduct=1666
[11:38:06.063][ 1252.531415] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11:38:06.063][ 1252.531425] usb 1-1: Product: DataTraveler 3.0
[11:38:06.074][ 1252.531434] usb 1-1: Manufacturer: Kingston
[11:38:06.074][ 1252.531442] usb 1-1: SerialNumber: 60A44C413841F28109956329
[11:38:06.085][ 1252.538996] usb-storage 1-1:1.0: USB Mass Storage device detected
[11:38:06.085][ 1252.562062] scsi host0: usb-storage 1-1:1.0
[11:38:06.095][ 1253.604840] scsi 0:0:0:0: Direct-AccessKingston DataTraveler 3.0PQ: 0 ANSI: 6
[11:38:06.108][ 1253.609019] sd 0:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[11:38:06.108][ 1253.610047] sd 0:0:0:0: [sda] Write Protect is off
[11:38:06.108][ 1253.610061] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
[11:38:06.119][ 1253.611083] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[11:38:06.144][ 1253.617545]sda: sda1
[11:38:06.144][ 1253.620597] sd 0:0:0:0: [sda] Attached SCSI removable disk

,

Shine：

我把您的问题升级到e2e了，请关注下面帖子的回复。因为美国过节，回复会晚一些。https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1064744/am5708-usb-dongle-can-t-work-with-usb-3-0