TI中文支持网Other Parts Discussed in Thread:TMDSHVMTRPFCKIT, TMDSCNCD28035, CONTROLSUITE
我这周刚刚购买了TMDSHVMTRPFCKIT，套件目前还未连接电机，且没有给套件的[Main]-P1供电。
我只通过[M6]-JP1给控制板TMDSCNCD28035上了电，控制板LD1常亮LD3闪烁，并且把[M3]-JP1 USB插口连接到了电脑。
之后，我按照QSG-HVMTRPFCKIT-GUIv2中的步骤将[Main]-J3,J4,J5,J9，和控制板上的开关检查了一遍，发现全按出厂的设置不需改动。
然后我打开C:\ti\controlSUITE\development_kits\HVMotorCtrl+PfcKit_v2.1\~GUI中的HVMTRPFCKIT-PM-ACI-GUI.exe，却发现设置之后无法连接。
设备管理器里没有XDS的AB通道，但是在端口中能看到XDS100设备
之后我进入CCS10.1，尝试查看JTAG的情况和进行调试，配置完Target Configurations，进行Test Connection时出现以下信息
[Start: Texas Instruments XDS100v1 USB Debug Probe_0]
Execute the command:
%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity
[Result]
—–[Print the board config pathname(s)]————————————
C:\Users\ADMINI~1\AppData\Local\TEXASI~1\
CCS\ccs1010\0\0\BrdDat\testBoard.dat
—–[Print the reset-command software log-file]—————————–
This utility has selected a 100- or 510-class product.
This utility will load the adapter 'jioserdesusb.dll'.
The library build date was 'Nov 8 2020'.
The library build time was '17:25:15'.
The library package version is '9.2.1.00042'.
The library component version is '35.35.0.0'.
The controller does not use a programmable FPGA.
The controller has a version number of '4' (0x00000004).
The controller has an insertion length of '0' (0x00000000).
This utility will attempt to reset the controller.
This utility has successfully reset the controller.
—–[Print the reset-command hardware log-file]—————————–
The scan-path will be reset by toggling the JTAG TRST signal.
The controller is the FTDI FT2232 with USB interface.
The link from controller to target is direct (without cable).
The software is configured for FTDI FT2232 features.
The controller cannot monitor the value on the EMU[0] pin.
The controller cannot monitor the value on the EMU[1] pin.
The controller cannot control the timing on output pins.
The controller cannot control the timing on input pins.
The scan-path link-delay has been set to exactly '0' (0x0000).
—–[The log-file for the JTAG TCLK output generated from the PLL]———-
There is no hardware for programming the JTAG TCLK frequency.
—–[Measure the source and frequency of the final JTAG TCLKR input]——–
There is no hardware for measuring the JTAG TCLK frequency.
—–[Perform the standard path-length test on the JTAG IR and DR]———–
This path-length test uses blocks of 64 32-bit words.
The test for the JTAG IR instruction path-length failed.
The JTAG IR instruction scan-path is stuck-at-ones.
The test for the JTAG DR bypass path-length failed.
The JTAG DR bypass scan-path is stuck-at-ones.
—–[Perform the Integrity scan-test on the JTAG IR]————————
This test will use blocks of 64 32-bit words.
This test will be applied just once.
Do a test using 0xFFFFFFFF.
Scan tests: 1, skipped: 0, failed: 0
Do a test using 0x00000000.
Test 2 Word 0: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 1: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 2: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 3: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 4: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 5: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 6: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 7: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
The details of the first 8 errors have been provided.
The utility will now report only the count of failed tests.
Scan tests: 2, skipped: 0, failed: 1
Do a test using 0xFE03E0E2.
Scan tests: 3, skipped: 0, failed: 2
Do a test using 0x01FC1F1D.
Scan tests: 4, skipped: 0, failed: 3
Do a test using 0x5533CCAA.
Scan tests: 5, skipped: 0, failed: 4
Do a test using 0xAACC3355.
Scan tests: 6, skipped: 0, failed: 5
Some of the values were corrupted – 83.3 percent.
The JTAG IR Integrity scan-test has failed.
—–[Perform the Integrity scan-test on the JTAG DR]————————
This test will use blocks of 64 32-bit words.
This test will be applied just once.
Do a test using 0xFFFFFFFF.
Scan tests: 1, skipped: 0, failed: 0
Do a test using 0x00000000.
Test 2 Word 0: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 1: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 2: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 3: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 4: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 5: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 6: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
Test 2 Word 7: scanned out 0x00000000 and scanned in 0xFFFFFFFF.
The details of the first 8 errors have been provided.
The utility will now report only the count of failed tests.
Scan tests: 2, skipped: 0, failed: 1
Do a test using 0xFE03E0E2.
Scan tests: 3, skipped: 0, failed: 2
Do a test using 0x01FC1F1D.
Scan tests: 4, skipped: 0, failed: 3
Do a test using 0x5533CCAA.
Scan tests: 5, skipped: 0, failed: 4
Do a test using 0xAACC3355.
Scan tests: 6, skipped: 0, failed: 5
Some of the values were corrupted – 83.3 percent.
The JTAG DR Integrity scan-test has failed.
[End: Texas Instruments XDS100v1 USB Debug Probe_0]
进入Debug后尝试Connect Target时报错
可能是因为该套件面市很久了，随套件寄来的U盘中资料是比较老的版本，里面附带的驱动和GUI文件夹中的exe文件都打不开，以上测试都是我在最新版本的Controlsuite和CCS10.1中进行的，我尽可能的详尽地描述我遇到的问题，希望大家能帮我解决和一起探讨。目前的猜测是不兼容的问题，但不知道是否与我未接入电机或者[Main]-P1有关。
Susan Yang：
Error -1135错误的相关说明，您可以参考：
software-dl.ti.com/…/ccsv7_debugging_jtag_connectivity_issues.html
该错误通常与C28x器件相关，并且通常与一系列硬件或固件问题相关，这些问题阻止了JTAG调试器连接到内核。
但由于手边没有TMDSHVMTRPFCKIT套件，所以暂时没法上手测试
,
Qilian Lin：
感谢您的回复，控制板上LD1s是绿色常亮的，LD3是红色闪烁的，然后套件板子上是灯也都正常，就不知为何连接不上。
已换过多台电脑尝试，都连接不上。
期待有更多的讨论。
,
Qilian Lin：
我可能需要更换我的CCS软件的版本
,
Susan Yang：
您可以在英文E2E上发帖，会有更多的同事一起为您回复
e2e.ti.com/…/c2000-microcontrollers-forum
,
Qilian Lin：
你好，请问如何维修TMDSHVMTRPFCKIT？我这个套件刚到手三天，还未接入过电机，强电部分从未运行过。只测试了一下控制板和JTAG，结果完全无法使用且根本找不到问题在哪。我就是在TI官网的网页上下单购买的，请问要怎样维修？
,
Qilian Lin：
我按照你的网页里的方法，外接了一个我自己的XDS100V2仿真器进行测试，结果还是不行。切换回板载仿真器后，原来应该能点亮的M3 LD1都不亮了，我不敢再调试了，想直接返厂维修。
,
Susan Yang：
这个还是建议您在英文E2E发帖，若是E2E内的工程师说明是套件本身的问题的话，您可以连续CSC
打开网页www.ti.com/csc–> 点击Chat with TI
,
Qilian Lin：
好的，谢谢
,
da qin zheng sheng：
你们以前接触过c2000没有?可能ccs版本高，工具版本低。
,
Qilian Lin：
英文E2E论坛需要企业邮箱啊，可是我只要学校和个人的邮箱，怎么办？
,
Qilian Lin：
感谢回复
肯定接触过，但是这是第一次用官方的套件，CCS6下也不能运行的，这个报错信息就是短路或者断路的报错。
,
Susan Yang：
请您跟踪/回复该帖子
e2e.ti.com/…/tmdshvmtrpfckit-can-not-connect-to-pc
,
Qilian Lin：
非常感谢。
,
Susan Yang：
不客气，后续有其他问题欢迎随时发帖
